DIY Bath Setup.
DIY Bath Setup.
Blog Article
The article following next relating to How to Install a Bathtub is amazingly fascinating. Check it out for yourself and see what you think of it.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the task can move easily; if you have to open a wall to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Instead of employing a professional to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly assist you install a new bath tub in your washroom if you have actually already purchased a brand-new tub and don't require to alter the arrangement of your previous water pipelines.
Your tools and product list must make up the following:
Getting ready for the Installment
To start with, the supporting frame provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent pressure on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub up until the level reads level.
To set up taps, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Activate the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if needed. Fill up the tub and also examine the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the tub should wait up until the bathtub has actually been utilized a minimum of once as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The former kind should be attached to the tap ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub remains in use. The sealant can split rather early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is a good idea to fit the tiles using waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our section about How to Install a Bathtub. Thanks a ton for taking a few minutes to read through our piece. Appreciated our post? Please share it. Let others locate it. Thank you for your time invested reading it.
Book Today! Report this page